Skip to main content

ACR-EX-100NILCD-I1-C

S0 Pulse Input to NB-IoT Converter with an LCD Display and Integrated Antenna​

Quick start guide for S0 pulse input to NB-IoT converter with an LCD display and integrated antenna ACR-EX-100NILCD-I1-C.

warning

WORK IN PROGRESS: This manual is currently being updated and may not contain all the necessary information.

ImageImage
Ordering CodeNetworkProtocolPower SourceMax. Devices
ACR-EX-100NILCD-I1-CNB-IoTS0 pulse counterC-Cell battery1
info

For further technical details, check the datasheet for NILCD-I1-C.

Installation Process​

1. Unscrew the 4 screws holding the lid, remove it and put it aside.​

ImageImage

2. If the box comes with a battery inside, put it outside of the box (for better handling) and insert a SIM card - if it is not pre-inserted.​

ImageImage

3. Run the interface cable through the cable gland and connect the conductors to the WAGO connector – each to a single entry. Make sure the contact is long enough (0,5 to 1 cm).​

ImageImage

4. Connect the battery to the JST-XH connector – to power up the device – and place it between the display and WAGO connector.​

ImageImage

5. Place the lid back on the box, align it and tighten the screws.​

ImageImage

6. Secure the device in place with screws and mounting holes or via other means such as cable ties - or in any other way according to your needs.​

ImageImage

7. Now you can configure the device via Optical Head - if needed.​

For further details, consult either the GUI Tutorial Article or the Configuration section below.

Configuration​

ACR-EX GUI is a graphical user interface for ACR-EX devices. It is a tool that allows you to configure and readout your ACR-EX devices.

Requirements​

To manage the ACR-EX device you need a Chromium-based browser (Google Chrome is recommended) and an optical probe.

IEC Optical Head
ORNO Optical Head – we may provide it to you as well if needed

Connecting to the GUI and configuring the device​

  1. Connect the optical probe to the computer via USB port.
ImageImage
  1. Open the browser and navigate to ACR-EX GUI.
    acr-ex_gui
  2. Click on the Connect button.
    acr-ex_gui
  3. The optical head should be detected (make sure the driver was installed), select it and click on the Connect.
    acr-ex_gui_port
  4. If you connected successfully, you should see the following screen.
    acr-ex_gui_port_init
  5. Tap the Magnetic Trigger on the side to enter the IEC Mode.
ImageImage
  1. Place the IEC Head on the top of the Metal Circle to begin a data transfer – both for configuration and data readout.
ImageImage

Showcase GIF

acr-ex_iec_gif
  1. You can either Load Config From Device or Show Default Values (of configuration).
    acr-ex_gui_loaded
  2. Configure the device config according to your needs.
  3. Press Save Config To Device.

Reading the archive​

  1. After connecting to the device, click on the Read Archive button.
    acr-ex_guiArchive
  2. Click on the Read Archive button.
    acr-ex_guiArchiveRead

Setting the counter​

  1. After connecting to the device, click on the Set Counter button.
    acr-ex_guiCounter
  2. You can either Load Counter or Set Counter.
    acr-ex_guiCounterLoaded
  3. Set the counter value and click on the Set Counter button.
    acr-ex_guiCounterSet

This article is currently work in progress. Please, contact us at support@acrios.com for any information that may be missing.
Further information can be found on wiki.acrios.com.
Last updated on by Ondřej Kaňovský